Plywood flooring is complete! I could not be happier with how this turned out and may end up doing the other rooms in our home with this same process. If you have not seen the process of creating the plywood flooring please check out the article here or the full video here.
Before I got started with staining I chose to run over the entire floor with a 150 grit power sander. I did not spend a whole lot of time on it just enough to take any dings, dents, and scuff marks out that I most likely added while installing the flooring. Once this was done I cleaned the entire room as best as possible with a vacuum and damp towels and we were ready for stain.
I chose a Minwax dark walnut stain to give the floor a dark old farmhouse kind of look. You can apply this stuff many ways but what I found to be the best was a homemade creation as usual:) I used an old Swiffer mop handle and head and stuck a cotton t-shirt to it. I dipped the contraption in the stain using a paint tray and then spread it on the flooring. This saved my back, a lot of time, and applied the stain fairly evenly.
After the first coat things were starting to look really good but a little bit lighter than we had hoped.
Two coats of the stain were applied about 24 hours apart which gave the floor a deep rich color that we absolutely loved. It was really starting to come together now. This is the point at which I began feeling relieved that this project was going to turn out exactly how we wanted it to.
Once the stain fully dried we were ready to start putting on the final protective coating. We chose a Minwax flooring polyurethane to seal the floor. This seemed to be the best, most durable, and easiest to apply option.
I started applying the poly one coat at a time with a small paintbrush. This method worked very well and although a bit slow, this stuff goes on very easily. I applied 4 coats of poly allowing each coat to dry for 6-12 hours before putting on the next. This is a quick drying poly so you can put it on in as little as 4 hours if you would like. I did not sand between coats; as directed this stuff is supposed to dry pretty flat without needing to sand each coat.
After 4 coats were applied I chose to do one round of sanding to knock out a few bumps I was starting to notice and some dog hair that somehow floated into the room and had dried into the finish, stinkin dog! I used a power sander with 220 grit paper and I did not push very hard at all while sanding. I just let the weight of the sander float on the floor until it was smoothed over very lightly.
Next I cleaned the floor with a damp cloth and applied the final coat of poly. I applied this final coat a bit thicker and let it dry over night.
After the final coat was dry the floor was safe to walk on and inspect and it looks awesome! It turned out much better than I could have imagined and the poly makes the flooring so durable. Even though this is a "soft" wood (pine) it is now very hard and resists scratches and scuffs very well. I will do a follow up on this project next year and update on how well it holds up to the changes in seasons and wear and tear or a 9 year old:)
How much did it cost? The room that I was covering was about 165 square feet and the total cost was about $253. This works out to about $1.50 per square foot and is much cheaper than traditional hardwood flooring.
Check out the full video here
Dark Walnut Stain - http://amzn.to/1jxBmnY
Polyurethane - http://amzn.to/1O2bSHJ
Porter Cable Brad Nailer - http://amzn.to/1O2chdh
All of these products and more recommended items from the SSL Family are available at the Simple
Suburban Living General Store
http://astore.amazon.com/simpsubulivi-20
Please follow us on....
http://www.pinterest.com/simplesuburban/
http://www.facebook.com/simplesuburbanliving
http://www.twitter.com/simplesuburban5
http://www.instagram.com/simplesuburbanliving
0 komentar:
Posting Komentar